Things you’ll need from your garage or we have available here at NAPA AUTO PARTS:
• Oil filter wrench set*
• Oil catch/recycle container
• Funnel
• New NAPA GOLD oil filter
• 4-5 qt. new oil**
• Clean rags
• Car jack
• Jack stands
• Safety glasses
• Mechanics work gloves
• Hand cleaner
*If you plan to change your oil regularly, consider investing in a small tool set, an oil filter wrench set and a quality floor jack and stands.
**Always check your owner’s manual. Some vehicles take up to 15 quarts!

Step 1

Park your car on a level surface and apply parking brake.
Run your engine for 5 minutes before draining oil, as warm oil drains faster than cold. Do NOT drain oil that is at full operating temperature. It will be way too hot! Remove your keys from the ignition, as some hybrid models can auto-start. To be safe, always check your owner’s manual before working on a specialty vehicle.

Step 2

Jack your car up and place it on jack stands.
A jack alone will not safely support the full weight of your car. Consult your manual for the proper jacking points. The placement of a jack stand is just as important as the jack placement. The wrong placement can damage your car’s suspension or body parts.

Step 3

Locate the oil drain plug and place the drain pan below.
The oil drain plug is usually near the front center of the engine, but some vehicles have more than one plug. Check your manual for the exact location. Then, loosen the plug with a socket wrench. Make sure that the drain pan is large enough to hold 4-5 quarts of oil or more. The oil drains at an angle, so position your pan to catch it.

Step 4

Unscrew the plug by hand.
Remove the plug by hand. While unscrewing the plug, push it back towards the pan. This prevents oil from rushing out until you are ready to remove the plug from the hole.

Step 5

Drain all oil.
To speed up the draining process, remove the filter cap located on the top of the engine and allow air to enter from the top. Check your owner’s manual for the exact location.

Step 6

Replace oil plug.
Tighten the oil plug by hand so it is not cross-threaded. Once the plug is tight, finish tightening with a wrench or by hand. Always use a new drain plug gasket and never over-tighten the drain plug.

Step 7

Remove existing oil filter.
Place the oil pan underneath the old filter to catch any remaining oil while unscrewing it, using an oil filter wrench. Use a rag to clean the mounting surface. Make sure that the sealing O-ring from the old filter is not stuck to the mounting surface on the engine.

Note: Some vehicles use remote mounted oil filters that may be on top or on the side of the engine.

Step 8

Lubricate new filter and screw into place by hand.
Lightly coat the rubber seal of the new filter with fresh oil. It’s usually not necessary to tighten the oil filter with the wrench. Refer to the filter’s instructions. Once the filter is installed, lower the car.

Step 9

Clean the oil filter neck and pour in the new oil using a funnel.
Typically, you will use 4 to 5 quarts of oil, but check your manual for your vehicle’s oil capacity. Fill to three-quarters of the engine’s capacity to avoid overfilling, as there is always oil that does not drain. Then replace the cap.

Step 10

Run the engine for a few minutes to make sure there are no leaks.
Check the area around the oil drain plug and the filter for any leaks. If you notice a leak, shut the engine off immediately and correct it or them. Check the dipstick afterward, and add more oil, if necessary.

Step 11

Dispose of the used oil properly.
Bring your used oil to a recycling center or bring it into NAPA and we’ll recycle it for you. These are the only acceptable methods for oil disposal.

Important Tips:
• Read your owner’s manual or see your local NAPA AUTO PARTS store specialists to ensure you are using the correct type of oil and oil filter.
• You’ll need to know the year, make, model and mileage of your car when you buy supplies at a NAPA AUTO PARTS store.
• Make sure your car is securely supported. You will need two jack stands to support the front of your car after jacking it up.
• Record the date and mileage after you change the oil so you will know when your car is due for another oil change. It helps to put a small sticker on your windshield to remind you.
• Handle hot motor oil with extreme caution.
• Use mechanic’s gloves to keep your hands protected and clean.
• Only dispose of used motor oil and filters at authorized locations.
• You can always bring your car to your local NAPA AutoCare Center and they will change your oil for you.